Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
Just how do you actually feel on the subject of How to Install a Bathtub?
Mounting a bathtub isn't specifically brain surgery, yet it does require strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a moderately difficult project. If the old tub is conveniently obtainable, the task can relocate immediately; if you need to open up a wall to remove the old bathtub and position the new tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have qualified on your own for the work and also are comfortable attempting it. As opposed to employing a contractor to take control of a halfway-completed project, it is far better to think about utilizing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This post will certainly assist you install a brand-new bathtub in your shower room if you have actually already gotten a new bathtub and don't require to transform the setup of your previous supply of water pipes.
Your tools and material checklist need to make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water supply. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing taps can be quite troublesome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will require lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin making certain that the washing machines remain in location in between the tap as well as the sink. Safeguard the faucet in position with the supplier offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous kind needs to be linked to the faucet ends initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for placement. The wood boards are practical in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four small points.
The following objective is to make sure that the bathtub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the bathtub up until the spirit level reads level.
To install faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water system as well as check all joints and also new pipework for leaks and also tighten them if essential. Load the bathtub as well as also inspect the overflow outlet and also the regular outlet for leaks.
Finally, repair the bath paneling as explained in the producer's instruction manual. Tiling and securing around the bathtub must wait till the tub has been used at least when as this will certainly resolve it right into its final position.
Planning for the Installment
First of all, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath must now prepare to be fitted in its final setting.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, causing issues with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before securing, to enable the movement experienced when the tub is in use. The sealer can crack rather very early if you do not take into account this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that section was a great idea. So long as you appreciated our blog posting plz be sure to pass it around. We take joy in reading our article about How to Install a Bathtub.
Contact Us Now Report this page